Instruction Manual 20Z704T-PZ10 Mini Speed Dome Camera Prior to Using This Document: Videology reserves the right to modify
7. Installation 7.1. DIP Switch Setup Before you install the camera, you should set the DIP switches to configure the camera ID, communication proto
Factory default of protocol is “Pelco-D, 2400 bps”. 7.1.3. Termination Switch Setting Termination switch (Pin 4) is used in cases listed below. • Lo
7.2. Direct Installation on the Ceiling 1) To pass cables to upside of ceiling, please, make about 50~60mm hole on the ceiling panel. 2) Detach
7.3. Installation using Ceiling Mount Bracket 1) Screw ceiling mount bracket to ceiling with screws. 2) Detach the marked part from the rubber gas
7.4. Installation using Wall Mount Bracket 1) Screw wall mount bracket to ceiling with 3 screws. 2) Detach the marked part from the rubber gaske
7.5. Cabling 7.5.1. Power Connection Please, check the voltage and current capacity of rated power carefully. Rated power is indicated in the back
7.5.3. Video Connection Connect with BNC coaxial cable 7.5.4. Network Connection (Reserved for future network models) 7.5.4.1. NETWORK 1 Connect with
8. Check points before operation Before power is applied, please check the cables carefully. The camera ID of the controller must be identical to
8.4. Preset Function Max. 127 positions can be stored as Preset position. The Preset number can be assigned from 1 to 128, but 95 is reserved for s
8.6. Pattern Function A Pattern Function memorizes the path of the joystick controller for an assigned time and relays the path exactly as it memor
Table Of Contents `1. Document History... 4 2. Important
8.7. Group Function The Group function allows running a sequence of Presets, Pattern and/or Swings. Max 8 group can be stored. Each group can have
GLOBAL/LOCAL WB (White Balance) and AE (Auto Exposure) can be set up Image Setup independently for each preset. There are 2 modes, "Global&
9. OSD Display of Main Screen LABEL 12345 PRESETAction Title F CAM 1 I: 1 ? ? ?15/4/x1/NAlarm Information P/T/Z Information Preset Label
10. Menu 10.1. General Rules of Key Operation for Menu • The menu items surrounded with “< >” always have a sub menu. • To enter all menu le
10.4. PRIVACY ZONE MASK Setup Select area in image to mask. Mask No [1~4] Select Mask number. If the selected mask contains data, a blank space ap
10.5. CAMERA SETUP Setup the general functions of zoom camera module. [AUTO/MANUAL/SEMIAUTO] Sets camera focus mode. Focus Mode SEMIAUTO Mode This
10.5.2. Auto Exposure Setup Backlight [ON/OFF] Enables Backlight Compensation Day/Night [AUTO1/AUTO2/DAY/NIGHT] AUTO1 changes Day/Night mode soo
10.5.3. White Balance Setup WB MODE [AUTO/MANUAL] In Manual mode, Red and Blue level can be set up manually RED ADJUST [10~60] BLUE ADJUST [10
Value Description Value Description C1 Low weight at the center of the screen C2 High weight at the center of the screen L1 Low weight at the
Jog Direction [INVERSE/NORMAL] Setting this to ‘Inverse’, the view in the screen is moving the same direction with jog, panning, and in reverse with
10.9.1. Edit Pattern... 33 10.10. Group Setup ...
10.7. PRESET Setup Preset Number [1~128] If a selected preset is already defined, camera moves to pre-defined position and preset characteristics s
10.7.1. Edit Preset Scene 1. Using the Joystick, move the camera to a desired position. 2. By pressing NEAR key, save current PTZ data. 3. Press
10.8. Swing Setup Swing Number [1~8] Selects Swing number to edit. If a selected Swing is not defined, "NOT USED" is displayed in 1st Po
10.9. Pattern Setup Pattern Number [1~4] Selects Pattern number to edit. If a selected pattern number is not defined, "UNDEFINED" wil
10.10. Group Setup Group Number [1~8] Selects Group number to edit. If a selected Group number is not defined, "UNDEFINED" will be displ
4. After finishing setting up an Action, press the Near key to one-upper level menu (Step 2). Move cursor Up/Down to select Action number an
10.12.1. Initial Configuration Table Display Configuration Camera Configuration Camera ID ON Focus Mode SemiAuto PTZ Information AUTO Digital
10.13.System Initialize (Variable Focus Lens Model) CLEAR ALL DATA Deletes all configuration data such as display, camera, motion setup and so on.
11. Specifications Electrical 20Z704T-PZ10 (NTSC) 21Z704T-PZ10 (PAL) Image Sensor 1/4" Interline transfer CCD Active Pixels (HxV) 768 x 494
11.1. Dimensions Main Unit & Surface Mount Bracket Ceiling Mount Bracket Doc # INS 20Z704T-PZ10 Issue Date: 08/13/2009 Revision: B Pag
1. Document History Revision Issue Date Reason CN# Rev A 06-30-09 Initial release 09-0101 Rev B 08-13-09 Section 4, 8.8, 10.5.2 revised 09-01
12. Contact Information For technical assistance with this product, please contact the supplier from whom the product was purchased. For OEM inqu
3. Precautions Operating • Before using, make sure power supply and others are properly connected. • While operating, if any abnormal condition or
4. Features Camera Specifications • CCD Sensor: 1/4" Interline Transfer CCD • Zoom Magnification: x10 Optical Zoom, x10 Digital Zoom (Max.
5. Product & Accessories 5.1. (10x/12x Zoom Models) Plastic Anchor 5.2. Product & Accessories (Variable Focus Lens Model) Plastic A
Ceiling Mount Bracket Wall Mount Bracket Doc # INS 20Z704T-PZ10 Issue Date: 08/13/2009 Revision: B Page 8 of 40
6. Parts Name & Functions Main Unit / Surface Mount Bracket Back of Main Unit Dome Cover (Bubble) Do not remove protection vinyl fro
Commentaires sur ces manuels